Operating system levels for Models Gxx Drivers are available for download from the Toshiba support Web site. Single Station Models The Single-station models are specifically engineered to deliver exceptional reliability and fast, quiet, high-quality thermal printing — even in harsh retail environments. Before Downloading these drivers, Please carefully read the following License Agreement. To install the program memory, complete the following steps: 1. Remove the long leg of the lift spring B in Figure 33 on page 60 from the mounting slot.
Common questions for Toshiba 4610 driver Q: Where can I download the Toshiba 4610 driver's driver? The following table provides a list of those cables and their part numbers. An improperly installed cable will result in no communication between the logic card and the thermal print head. Press down on the side of the interface card opposite the tab until the blue release button slider snaps into place. Rotate the interface card toward the printer until is clicks into place. The printer is capable of printing verification information on a check and printing information on an inserted document. Set the card down on the static-protective package. A list of supported paper and suppliers are available from the Toshiba support site.
You shall not copy or make a duplicate or backup copy of this Software, in whole or in part, except as otherwise expressly provided herein. B-4 © Copyright Toshiba Global Commerce Solutions, Inc. Important: The methods of installing the seal as well as the type of seal used is country specific. See the information provided by the fiscal authority in your country for details about the type of seal and how to install it. The materials at those Web sites are not part of the materials for this Toshiba Global Commerce Solutions product and use of those Web sites is at your own risk. Click on Device Manager button. Note: Ensure that the ground strap A in Figure 31 makes contact with the tab B in Figure 31 on the logic card.
Oregon: For information regarding recycling covered electronic devices in the state of Oregon, go to the Oregon Department of Environmental Quality site. Plus, the latest models offer innovative electronic check processing. Place the printer unit upside down on a flat work surface. This connector can drive either a single cash drawer using either the short Cash Drawer Cable or the Long Cash Drawer Cable or two cash drawers using a special cable. Release both buttons when the Printer Ready indicator begins to blink. Note: If the logic card is to be reinstalled, take precautions to avoid damage from static electricity. For Models Gxx, the character set is controlled by the fiscal module and cannot be modified by the user.
Remove the electronic journal slot card The fiscal logic card does not have to be removed from the tray to remove the electronic journal slot card from its mount on the logic card. Ensure the electronic journal card is right side up and attempt to insert it in the slot again. During the removal process, the printer must be placed upright and you will have to locate the tab by feel. The Knowledgebase located near the bottom of the page provides access to previously asked questions and their answers. If print quality still does not improve, call for service.
Depending on the model, some features might not be available, or some specifications might not apply. September 2013 This edition applies to the Toshiba 4610 SureMark Fiscal Printer models listed in Table 1-1 on page 1-1. Discard the empty paper roll core. Problem determination Any problems that arise with a SureMark printer are either software errors or hardware failures. Ribbon Shield Printhead Correct Not Correct Figure 2-5. Removing the Check Flipper Cartridge 4.
This site contains additional information that is gathered from field experience, and might not have been available at the publishing date of this document. Upon the termination of this Agreement, you agree to have the Software un-installed and destroy it. Note the position of the cables connected to the logic card; then, disconnect them. To install the logic card, complete the following steps: 1. The two-station models include a direct thermal customer receipt station plus an impact slip printing station for multipart forms and checks.
If the card does not go into the slot, do not force it. The logic card can now be set aside in a static-protective package. Refer to Figure 16 on page 40. Insert the paper into the two halves of the plastic paper receiver. Where to find more information Current versions of Toshiba publications are available on the Toshiba support Web site. It describes the diagnostic tools that are available, error codes and suggested actions, and instructions for replacing failing components.
Code Page 860 4610 SureMark Three— Station Printer: User's Guide. Upon entering the off-line test mode the following off-line selection menu is printed. Flat panel displays The fluorescent lamp in the liquid crystal display contains mercury. Printer's Resident Character Set - Generic Code Page Appendix B. To check for updated printer paper information, complete the following steps. It is available to install for models from manufacturers such as Ibm and others. Place the main frame of the printer on to the fiscal base.